Showing posts with label WiMAX Radio. Show all posts
Showing posts with label WiMAX Radio. Show all posts

Thursday, March 25, 2010

Radio Engineering Consideration for WiMAX Systems

WiMAX solutions include fixed WiMAX and mobile WiMAX. According to the type of terminal offered (outdoor CPE (Consumer Premise Equipment), self-install indoor CPE, mobile terminal–PCMCIA, laptop, smart phones), each solution has a different deployment method.

LOS/NLOS Propagation
Coverage from a BS is linked to several radio parameters. The first one is the propagation environment. Depending on the relative locations of the BS and the terminal, several models can be used to evaluate the losses due to propagation.

LOS and Near LOS Propagation
Line-of-Sight (LoS) and Near Line-of-Sight (NLoS) propagations may happen when the BS and the MS are deployed outdoor, above the average height of the environment. This may be the case of the deployment of a fixed WiMAX solution in a rural environment with the BS located on a high altitude point (or at the top of a mast) and the SS (then a CPE, for a fixed WiMAX) deployed on the rooftop of the customer's house.

LOS propagation requires that the first Fresnel zone is free from any obstacle. In that case, the propagation losses are proportional to the square of the distance between the BS and the SS. However, in a practical deployment, this happens very seldom. Usually, the Fresnel zone is obstructed and/or there are few obstacles on the BS to the CPE transmission path. In that case, near LOS models are used. However, in the case where there are few obstacles (a building, a water tower, a hill), the obstacles are modelled by knife-edge. An example of such a model can be found in Reference.

NLOS Propagation
NLOS (Non-Line-of-Sight) propagation occurs when the terminal is located indoor and/or at ground level. In this situation, there is in most cases no direct path between the BS and the terminal, there is a high number of obstacles on the BS to MS path (buildings, trees, cars, etc.) and the receiver may receive several copies of signal that experienced several reflections/diffractions on different obstacles. This type of propagation is typical of cellular deployments.

In the case of WiMAX, NLOS propagation corresponds to a deployment of a fixed or mobile WiMAX using self-install indoor terminals (wireless DSL deployment), or a deployment of a mobile WiMAX with mobile terminals (PCMCIA, laptop with integrated chipset, multimode mobile phones, etc.).

In NLOS, the losses versus the distance are much higher that in LOS. Usually, the distance decay exponent is between 3 and 4. An example of a propagation model that can be used to evaluate propagation losses in NLoS is the Erceg model.

Radio Parameters and System Gains
In order to evaluate the range, additional parameters are required. First, the value of some propagation parameters depends on additional radio parameters such as:


  • Frequency band. WiMAX could be deployed at different frequencies (2.3 GHz, 2.5 GHz and 3.5 GHz); the higher the frequency, the higher the propagation losses.
  • BS antenna height. Propagation losses decrease if the antenna height is increased.
  • Terminal antenna height. The lower the terminal, the higher the losses (for mobile deployment, the height of the terminal is usually taken to be between 1.5 and 2m).


Then, depending on the deployment scenario, a margin modelling the fluctuations of the radio environment needs to be considered.

In the case of the LOS/near LOS scenario, the BS and the MS are fixed. However, the propagation loss fluctuates (according, for example, to geoclimatic parameters). Hence, to evaluate the range, a margin needs to be evaluated according to the signal availability required (e.g. 99%) and the geoclimatic parameters. A method to evaluate the margin is available in Reference.

In the case of the NLOS scenario, in order to reflect the distribution of the obstacles in the coverage area, a margin, called the shadowing margin, needs to be taken into account for the evaluation of the range. This shadowing effect is modelled by a lognormal distribution with a standard deviation, which depends on the environment (typically from 10dB in an urban environment to 5 dB in rural environments). The resulting margin also depends on the signal probability availability on the cell area (usually between 90 and 95%). In addition, other margins may be included in the propagation losses: indoor margin (in the case of indoor coverage requirements), interference margin (to reflect the interference level generated by other cells transmitting at the same frequency), body losses, etc.

Finally, to evaluate the range, the system gain may be evaluated. The system gain is the maximum signal level difference that can be accepted on the BS-to-terminal path so that the receiver may decode a signal with sufficient quality. The system gains depend on many specific parameters:


  • Transmission power of the BS/terminal.


  • Antenna gain of the BS/terminal. The gain at the terminal side depends on the type of terminal. Outdoor CPEs may have gains in excess of 14dBi while mobile terminals may have only a 0dBi antenna gain.


  • Receiver sensitivity. The receiver sensitivity depends on the signal bandwidth, the modulation and the coding scheme. The IEEE 802.16 standards are providing minimum reference values but vendors may come with better performance solutions.


WiMAX Radio Features that Enhance the Range
For fixed WiMAX solutions deploying outdoor CPEs, the coverage may be of several km. However, to get range figures in line with an exiting cellular system for WiMAX cellular-like deployments, additional features are needed to compensate for the extra losses due to lower terminal antenna gains, indoor penetration and NLOS behaviour.

The radio enhancement feature applicable to fixed and mobile WiMAXs is subchannelisation. This is the possibility to concentrate the transmit power on a few subchannels and thus to play with trade-off between the coverage and the maximum data rate a terminal can get at the cell edge. Other enhancement features that are only applicable to the mobile WiMAX are:


  • Convolutional Turbo Coding (CTC).
  • Repetition Coding. For each retransmission, up to 3 dB gain can be obtained. This again allows a trade-off between the maximum range and data rate at the cell edge.
  • Hybrid ARQ (HARQ). This is the capability of the receiver to combine several transmissions of the same MAC PDUs.
  • Advanced antenna technologies: beamforming and MIMO.


Frequency Planning Guidelines
Again, according to the deployment scenario, the frequency planning guidelines are different.


  • Fixed WiMAX

In the case of a fixed WiMAX with an outdoor CPE deployed in LOS/near LOS, similar frequency planning to that of Fixed Wireless Access (FWA) systems (e.g. PMP microwave transmission) can be used. At the radio site, several alternatives for sector configurations may be employed (1, 3, 4 and 6 sectors per site). In FWA-like deployment, the CPE has an external antenna with high gain and hence a reduced antenna beam width. Consequently, the antenna of the CPE provides significant interference protection; hence in order to achieve the CINR target on the service area, frequency planning with 3 and 4 frequencies may be used. For the fixed WiMAX with an indoor self-install CPE, which also have directive antennas, a similar frequency plan may be used.

For densification, more sectors (up to six) or more frequencies per sector can be deployed on the existing sides.


  •  Mobile WiMAX

In the case of a mobile WiMAX deployment with mobile terminals, there is no interference reduction due to the MS antenna (omnidirectional antennas). However, because of the use of OFDMA and permutations (which gives some randomness in the use of subcarriers), and because of the better radio performance (more coding capabilities, beamforming and/or MIMO), it is possible to deploy an efficient system with a frequency planning reuse scheme of 3 and even 1.

In the case of MBS (see below), the frequency channel assigned for transmitting multicast/broadcast connections must be deployed in a Single Frequency Network (SFN) manner.

For densification, the same techniques used for existing cellular systems are employed: more frequencies per site, cell splitting, microcellular layer, indoor coverage from the indoor, etc.

Base Station Synchronisation
IEEE 802.16-2004 indicates that there are three options of BS synchronisation:


  • Asynchronous configuration. Every BS uses its own permutation. The frame lengths and starting times are not synchronised among the base stations. This configuration can be used as an independent low-cost hot-spot deployment.
  • Synchronous configuration. All the BSs use the same reference clock (e.g. by using GPS, or Global Positioning System). The frame durations and starting times are also synchronised among the BSs but each BS may use different permutations. Due to the time synchronisation in this scenario and the long symbol duration of the OFDMA symbol, fast handovers as well as soft handovers are possible. This configuration can be used as an independent BS deployment with a controlled interference level.
  • Coordinated synchronous configuration. All the BSs work in the synchronous mode and use the same permutations. An upper layer is responsible for the handling of subchannel allocations within the sectors of the base station, making sure that better handling of the bandwidth is achieved and enabling the system to handle and balance loads between the sectors and within the system.

The standard indicates that, for TDD and FDD realisations, it is recommended (but not required) that all BSs should be time-synchronised to a common timing signal.

Saturday, November 7, 2009

Logical Channels | WiMAX Radio

Logical channels are a portion of a physical communications channel that is used for a particular (logical) communications purpose. The WiMAX physical channel can have up to 65,535 logical channel connections and each connection can multiple service flows associated with it.

Connection ID (CID)

WiMAX logical channels are identified by a connection identifier (CID). A CID is a unique name or number that is used to identify a specific logical connection path in a communication system. Some connection channel IDs are reserved for control (management connection) and other connections are used for transporting user data.

Each type of connection has its own CID. A two-way connection requires two CIDs. For basic, primary and secondary connections, CID codes are assigned in pairs and they are the same for the downlink and uplink connections.

An initial ranging connection identifier is a code that is used during the initial connection to a wireless system to determine how much transmission timing adjustment is required. For WiMAX systems, the initial ranging CID is 0000 for standard transmission systems and FEFF for adaptive antenna systems.

A basic CID is a logical channel that is assigned during the initial ranging process. Basic CID connections are used for time sensitive MAC control messages such as RF power control and time alignment. The range of CIDs that can be assigned for basic CIDs is from 0001 to some number (m) selected by the operator.

A primary management CID is a logical channel that is used to transfer link control messages. The range of CIDs that are assigned as primary CIDs ranges from the address above the highest basic CID (m+1) to double the number of basic CIDs (2m).

A secondary management CID is a logical channel that is used for upper layer control messages such as DHCP and TFTP messages. The range of CIDs that is assigned as secondary management CIDs ranges from the address above the highest primary management CID (2m+1) up to connection ID FEFE.

A transport CID is a logical channel that is used to transfer user data. The range of CIDs that are assigned as transport CIDs ranges from the address above the highest primary management CID (2m+1) up to connection ID FEFE. Transport connections can use different CIDs in the uplink and downlink directions.

Multicast polling connection identifiers are used to prompt subscriber stations which are part of a multicast group that have data to transmit to attempt to transmit their data using a contention control process. The multicast polling CIDs range from FF00 to FFFC.

A broadcast connection identifier is used to transfer broadcast messages to all devices that are listening to the radio channel. The broadcast CID is FFFF.

Figre 1 outlines some of the CID codes that are used in the WiMAX system. The table shows that CID 0000 is reserved for initial ranging and the basic, primary, secondary and transport CIDs are dynamically assigned as needed. Other reserved CIDs include FEFF for adaptive antenna initial ranging, FF00 through FFFC for multicast polling, FFFD for fragmental broadcast messages, FFFE for padding messages and FFFF for broadcast messages.

Figure 1: WiMax CID Codes


Service Flow ID (SFID)

A service flow identifier is a unique number that is assigned by a system that is used to identify the flow of a communication channel that is used for a specific service type. A WiMAX device may have multiple SFIDs per connection (per CID).

Figure 2 illustrates that the WiMAX system has logical connection and service flow channels. Each subscriber station has at least one connection channel and service flows may be assigned to the connections. In this diagram, a WiMAX base station has setup connections with 3 WiMAX subscriber stations. For home #1, the WiMAX transceiver connection is providing one type of service flow for an Internet web browser over a single connection. For home #2, the WiMAX base station has setup a single connection with two services flows; one for a web browsing computer and the other for an IP telephone. For the office user, the WiMAX base station has setup 3 connections on a single subscriber device (3 CIDs). Of these, 2 connections have 2 service flows providing web browsing and IP telephone service and the 3rd connection has a single service flow for web browsing service.

Figure 2: WiMax Logical Channels

Thursday, November 5, 2009

Retransmission Policy | Wimax Radio

Retransmission policy (automatic repeat request – ARQ) is the set of rules or processes used by networks to define if, when, and how retransmissions of data or information will occur. Some types of services (such as real time digital audio) do not use retransmissions because the delay for retransmission would take too long to offer any benefit.

Retransmission uses error detection, feedback, retransmission processes and the retransmission of blocks of data in packets. The WiMAX system uses two forms of ARQ; hybrid automatic repeat request (HARQ) and selective repeat (SR).

Selective Repeat (SR)

Selective repeat automatic repeat request is a data transmission control process that allows the receiver to request the retransmission of selective blocks of data.

Data to be transmitted is grouped into blocks and given a block sequence number (BSN). The maximum size of a data block in the WiMAX system is 2040 bytes. When blocks are transmitted using ARQ, each block is given a sub-packet identifier (SPID). An SPID is an index value that can be used to identify specific packets that are awaiting conformation in an automatic repeat request (ARQ) process.

As blocks are transferred between the sending device and the receiving device, acknowledgement messages are sent. WiMAX acknowledgement message types include selective, cumulative and cumulative with selective. ARQ messages can be sent as separate messages or the may be combined with other messages.

Hybrid Automatic Repeat Request (HARQ)

Hybrid automatic repeat request is a data transmission flow control process that uses a combination of the physical layer (PHY) and medium access control (MAC) layer to allow the receiver to stop and restart the retransmission of data over a transmission channel.

HARQ is a variation of a stop and wait ARQ. Stop and wait ARQ is a flow control process that allows the data flow to stop when packets are not received and wait until a successful retransmission is received before the data flow is restarted.

Monday, November 2, 2009

Sub Channelization (Sub-carriers)

Sub channelization is the dividing of communication channels into smaller sub-parts. The air interface portions of the WiMAX system divide a wide radio channel into several sub-carriers. A sub-carrier is a modulation signal that is imposed on another carrier that can be used to independently transfer information from other sub-carriers located on the radio channel. The WiMAX system sub-carrier signal types include a pilot sub-carrier (reference signal), guard sub-carrier (interference protection) and data sub-carrier (user information).

A pilot sub-carrier is a reference signal that serves as a control signal for use in the reception of other sub-carrier signals. A guard sub-carrier is one or more sub-carriers on a communication channel that is not used (null channel). The guard sub-carrier is dedicated to the protection of a communication channel from interference due to radio signal energy or time overlap of signals. Data sub-carriers are transmission channels that carry user information or data. Sub-carrier signals are referenced from the center of the radio channel. The sub-carrier that is located at the center of the radio channel is called the DC sub-carrier.

The number of sub-carriers in the WirelessMAN-OFDM system is 256. Of these, 55 are reserved as guard bands and 8 sub-carriers are used to transfer reference pilot signals. This allows up to 192 sub-carriers to be used for data transfer.

For a 20 MHz WiMAX OFDMA radio channel, there may be 2048 subcarriers. Of these, approximately 70% can be used as data carriers, 25% are reserved to protect from interference (guard bands) and approximately 15% are used as reference signals (pilot channels).

Figure 1 depicts how the WirelessMAN-OFDM system divides a wide radio channel into several independent orthogonal channels with smaller bandwidth. The sub-channel in the center of the RF channel is called the DC subcarrier. Some of the sub-carriers are used as reference pilot channels and some are reserved for guard bands.

Figure 1: WiMax OFDMA Sub Channelization

Friday, October 23, 2009

Ranging (Dynamic Time Alignment) | WiMAX Radio

Ranging is a dynamic time alignment process that allows a radio system base station to receive transmitted signals from mobile communication devices in an exact time slot, even though not all mobile communication devices are the same distance from the base station. Ranging keeps different mobile device transmit bursts from colliding or overlapping. Ranging is necessary because subscriber stations may be moving or have been moved, and their radio waves’ arrival time at the base station depends on their changing distance from the base station. The greater the distance, the more delay in the signal’s arrival time. Transmission delay is approximately 3 microseconds per km (or 5 microseconds per mile). To perform time alignment, a subscriber station can advance or delay its transmission timing relative to the reference message that it receives on the downlink channel.

Figure 1: WiMax Adaptive Time Division Duplex (ATDD) Transmission

The WiMAX system uses two types of ranging: initial ranging and periodic ranging. During initial ranging, the WiMAX subscriber station transmits a brief ranging request message that allows the system to send back a ranging response message with the amount of timing offset that the subscriber station must use when it begins transmitting. After the subscriber station has attached to the system, the base station will continually send time alignment messages (periodic ranging) to the subscriber station to adjust (fine tune) its timing advance as it moves in the radio coverage area.

Initial ranging is the process of time aligning with a communication system before establishing a communication session. The initial ranging process involves synchronizing to an incoming transmission channel, sending a request at a particular time interval relative to the received channel and obtaining a response that allows for the time synchronization with the device or system.

Periodic ranging is the process of continuous time alignment with a communication system during a communication session. The periodic ranging process involves maintaining synchronization with an incoming transmission channel, periodically transmitting messages (such as sending user data) and receiving time alignment information from the other device or system.

If the subscriber station is continually communicating with the base station (receiving or transmitting data), the system can sense changes in the timing and send time alignment messages along with other packets of data to the subscriber station. If a significant amount of time has elapsed since a subscriber device has communicated with the system, the BS must initiate polling requests to reinitiate the ranging process.

Figure 2 shows how the relative transmitter timing in a subscriber station (relative to the received signal) is dynamically adjusted to account for the combined receive and transmit delays as the WiMAX radio is located at different distances from the base station antenna. In this example, the subscriber station uses a received burst to determine when its burst transmission should start. As the subscriber station moves away from the tower, the transmission time increases therefore causing the transmitted bursts to slip outside its time slot when it is received at the base station (possibly causing overlap to transmissions from other radios.) When the base station receiver detects the change in slot period reception, it sends commands to the subscriber station to advance its relative transmission time as it moves away from the base station and to be delayed as it moves closer.

Figure 2: WiMax Ranging

Tuesday, October 20, 2009

Duplex Transmission | WiMAX Radio

Duplex transmission is the simultaneous transmission of two information signals that allows simultaneous (or near simultaneous) 2-way communication. The WiMAX system can use frequency division duplex (FDD), time division duplex (TDD) or half frequency division duplex (H-FDD).

FDD is the process of simultaneously allowing the transmission of information in both directions via separate frequency bands. When using FDD, each device transmits on one frequency while listening on a different one.

TDD refers to the process of allowing two way communications between two devices by time-sharing. When using TDD, device 1 transmits while device 2 listens for a short period of time. After the transmission is complete, the devices reverse their role so device 1 becomes a receiver and device 2 becomes a transmitter. The process continually repeats itself so data appears to flow in both directions simultaneously.

H-FDD is a process that allows for two-way communications between two devices through the combination of frequency division and time sharing. When using H-FDD, device 1 transmits on one frequency while the device 2 listens for a short period of time on that frequency. After the transmission is complete, the devices reverse their roles and device 2 transmits on a different frequency and the other device listens for a short period of time on that frequency. The process continually repeats itself so data appears to flow in both directions simultaneously. The use of H-FDD systems allows for the simplification of radio design as the transmitters and receivers in the same unit are separated in both frequency and time so a duplex filter is not required.

As shown in Figure 1, the WiMAX system may use three types of duplexing: frequency division duplex (FDD), time division duplex (TDD) and half frequency division duplex (H-FDD). FDD allows the transmission of information in both directions at the same time by using separate frequency bands ( frequency division). Half frequency division duplex uses different frequencies for transmission but does not allow transmission and reception at the same time.

Figure 1: WiMax Duplex Transmission

When operating in time division duplex mode, WiMAX devices require reserved time periods to allow for transmission time (guard time) and to allow the device to transition between receive and transmit modes (transition gap).

Guard time is an amount of time that is allocated within a single time slot period in a communication system to help ensure variable amounts of transit times (e.g. from close and distant transmitters) do not cause overlap ( collisions) between adjacent time slots. Transmission of information does not occur within the guard period.

Receive-transmit transition gap is the amount of time that is allocated between the reception of a packet and transmission of a packet in a time division duplex (TDD) system. Transmit-receive transition gap is the amount of time that is allocated between the transmission of a packet and the reception of a packet in a time division duplex (TDD) system.

WiMAX systems have the capability to dynamically change the amount of bandwidth that is transmitted in either direction through a process called adaptive time division duplex (ATDD). ATDD is a process of allowing two way communications between two devices by time sharing on the same communication channel (e.g. the same frequency) and the amount of transmission rate or time that is used by each device can dynamically change.

Figure 1 illustrates how the WiMAX system can use adaptive time division duplex transmission to vary the amount of bandwidth that is transferred in either direction. A base station initially sends data at a high rate. However, after the user has received the data, the base station begins to send a response at a high rate. The time periods allocated for transmission on the downlink and uplink continually vary to allow for variable data transmission rates.

Saturday, October 17, 2009

Channel Coding | WiMAX Radio

Channel coding is a process where one or more control and user data signals are combined with error protected or error correction information. The WiMAX system channel coding processes include error correction coding, interleaving and randomization.

Error Correction Coding

Error correcting codes are additional information elements that are sent along with a data signal that can be used to detect and possibly correct errors that occur during transmission and storage of the media. Error correction codes conform to specific rules or formulas to create the code from the data that is being sent. Error correction codes require an increase in the number of signal elements that are transmitted which increases the required data transmission rate. The WiMAX system can use a variety of error coding methods including Reed Soloman coding, convolutional coding (optional) and block turbo coding (optional).

Interleaving

Interleaving is the reordering of data that is to be transmitted so that consecutive bytes of data are distributed over a larger sequence of data to reduce the effect of burst errors. The use of interleaving greatly increases the ability of error protection codes to correct for burst errors. Many of the error protection coding processes can correct for small numbers of errors, but cannot correct for errors that occur in groups. The WiMAX system uses interleaving to map data onto non-adjacent sub-carriers to help overcome the effects of frequency selective (e.g. multi-path) distortion.

Randomization

Randomization is a process that rearranges data components in a serial bit sequence to statistically approximate a random sequence. For communication systems, randomization involves using a known randomization code or process in the transmitter and using the same code to decode the randomized sequence at the receiver.

The WiMAX system uses a pseudo-random binary sequence (PRBS) randomization process that ensures that there are no long sequences of bits that would cause the modulator to produce a high peak to average power ratio (PAPR) signal. PAPR is a comparison of the peak power detected over a period of sample time to the average power level that occurs over the same time period. A high PAPR would require the use of a more linear RF amplifier assembly increasing cost and decreasing power conversion efficiency (e.g. shorter battery life).

Wednesday, October 14, 2009

Channel Descriptors | WiMAX Radio

Channel descriptor is a set of information parameters that describe the characteristics associated with a communication channel. The use of a channel descriptor can permit more accurate and successful reception and decoding of information that is sent on a communication channel.

The WiMAX system periodically sends (broadcasts) channel descriptors on the downlink channel to allow the subscriber stations to understand how to decode and transmit messages. Channel descriptors provide information about the uplink and downlink channels.

The downlink channel descriptor contains a downlink frame prefix that provides the information to the receiver about the frame structure of the downlink channel and a downlink map (DL-MAP) that defines what information will be transmitted. The DL-MAP contains a downlink interval usage code (DIUC) that defines when information will be transmitted on the downlink and what formats it is supposed to use (burst profile).

The uplink channel descriptors contain an uplink map (UL-MAP) message that defines when a subscriber station is allowed to transmit on the uplink and what formats it is supposed to use (burst profile). The UL-MAP contains an uplink interval usage code (UIUC) that defines when a subscriber station is allowed to transmit on the uplink and what formats it is supposed to use (burst profile).

Figure 1 demonstrates how the WiMAX system uses channel descriptors to define the allocated times and burst types that are used on WiMAX radio channels.

Figure 1: WiMax Channel Descriptors

Sunday, October 11, 2009

Radio Packets (Bursts) | WiMAX Radio

A radio packet is a short transmission (a burst) of information that occurs on a radio channel. Radio bursts contain reference sequences (preamble and possible a midamble), control information and payload of data.

The radio packet burst may have different types of radio characteristics such as modulation type, error coding, preamble length and transmission guard time periods. The combination of these characteristics is called the burst profile.

A burst set is a single transmission (RF packet) that contains a preamble along with one or more bursts of information. The bursts of information contained within the RF packet may have different modulation and coding types. A burst frame is the complete set of information that is contained in a transmission burst.

The bursts within a burst set are sequenced according to their modulation complexity. Bursts with lower complexity modulation types are located at the beginning of the radio packet. Bursts that follow can use modulation types with higher complexity (e.g. QPSK, QAM). This allows subscriber stations to receive and decode all the bursts up to the burst with the highest modulation type it can receive.

RF bursts start with a sequence of bits (a preamble) that the receiving device can recognize and lock onto. Once the receiving device locks onto the preamble, it knows where to find the rest of the packets.

For longer RF bursts, midamble sequences may be periodically inserted to assist receivers in the decoding of bursts. A midamble is a sequence of bits that the receiving device can recognize and lock onto to help decode the bits surrounding the midamble. Increased mobility (speed) can be tolerated when preambles and midambles are sent more frequently.

Burst profiles may continually change on a WiMAX system. Subscriber stations can send burst profile change request messages that define a desired new burst profile characteristic (such as modulation type or error coding). The request may be a result of an increase in the error rate using an existing burst profile.

Data packets may be inserted (embedded) within the payload of a single RF burst, they may be divided (fragmented) so they can be distributed over several radio packet bursts or multiple small packets may be combined (packed) into the payload.

Figure 1 depicts an example of a WiMAX radio packet which is made of a preamble and a set of bursts. The figure shows that the modulation type of the burst starts simple (BPSK) and gets more complex as additional bursts follow.

Figure 1: WiMax RF Packets

Thursday, October 8, 2009

Medium Access Control Protocol Data Units (MAC PDUs)

Medium access control protocol data units are a package of data (group of data bits) that contain header, connection address and data protocol information that is used to control and transfer information across a type of medium (such as a radio channel). The WiMAX system MAC PDUs contain a header, which holds the connection identifier along with control information. MAC PDUs may also have payload of data and error checking bits (CRC) bits after the header (e.g. user data). A MAC PDU header contains a header type, encryption control field, payload type and error checking (CRC) code.

A header type is a data field within the packet header that indicates the type of the header. The header type typically indicates the field format of the header and/or sub-headers that are part of the data packet.

Encryption control is the transferring parameters or sending of signaling messages in a data field within the header of a data packet that indicates encryption is used and possibly the type of encryption that is used. An encryption control field in a header typically indicates the payload of the data packet is encrypted.

Payload type is a data field within a packet header that indicates the format of the payload of data including any sub-headers

A cyclic redundancy check indicator is a data field within a packet header that indicates if and how a CRC error check code is used for the packet of data.

Encryption key sequence is an index value that is used to identify the location of a data packet within a sequence of packets to enable the decryption of the packet.

A length field is a data field within a packet header that holds a number or value that indicates the length of a data packet or a block of data.

A connection identifier is a unique name or number that is used to identify a specific logical connection path in a communication system. For the WiMAX system, the connection identifier is a 16 bit code.

A header check sequence is a calculated code that is used to check if the bits within a header have been received correctly during transmission.

Figure 1 shows the typical construction of generic WiMAX medium access control packet. This diagram shows that generic WiMAX MAC data packets contain addressing and controlling information and the payload can have variable length. This diagram shows that the MPDU header is 6 bytes long and that the header type indicator is used to determine which, if any, subheaders may be used.

Figure 1: WiMax MAC PDU

Monday, October 5, 2009

Addressing | WiMAX Radio

Each WiMAX radio is configured at the factory with a unique 48 bit medium access control address (MAC address) as identified in IEEE standard 802-2001. The first few bits of the MAC address indicate the manufacturer of the device. The remaining bits are a unique serial number of the device. While it is possible for a single subscriber device to have more than one 48 bit physical MAC address, most devices have a single MAC address.

The 48 bit MAC address is not part of the transmitted packet (MPDU). Instead, the device is identified by a 16 bit connection identifier (CID) that is assigned after the device has connected to the system. The MAC address is transferred during the device registration or authentication process to allow the system to identify the specific user. A single WiMAX device may contain 1 or more globally unique MAC addresses.

Each WiMAX device typically has several CIDs assigned. Some of the CIDs are used for controlling information and some are used to identify user data transmission channels (traffic channels).

The 16 bit CID is used to identify and categorize traffic (a maximum of 65,535 CIDs can exist per RF channel). Some CIDs are pre-assigned for specific functions (such as initial ranging) and others are unique to a specific connection.

A single CID may be shared by several services (logical channels). Each of these channels is a service flow and is identified by a service flow identifier (SFID).

To reduce the amount of overhead on a WiMAX radio channel (bits dedicated for control purposes), a shortened version of a CID (called a reduced connection identifier) may be used. A reduced connection identifier (RCID) can be 11, 7 or 3 bits long.

Saturday, October 3, 2009

Radio Propagation | WiMAX Radio

Radio propagation is the process of transferring a radio signal ( electromagnetic signal) from one point to another point. Radio propagation may involve a direct wave (space wave) or a wave that travels along the surface (a surface wave). Radio propagation characteristics typically vary based on the medium of transmission (e.g. Air) and the frequency of radio transmission. WiMAX systems may be operated as line of sight (direct transmission path) or non line of sight (indirect transmission path) systems.

WiMAX systems are typically designed with a radio link budget. A link budget is the maximum amount of signal losses that may occur between a transmitter and receiver to achieve an adequate signal quality level. The link budget typically includes cable losses, antenna conversion efficiency, propagation path loss, and fade margin.

Due to transmission impairments, a fade margin is budgeted in a communication link. Fade margin is the amount of signal loss, usually expressed in decibels, that a radio signal in a communication path is anticipated to change (or budgeted to change). This helps to ensure that typical signal fading periods do not result in a lower than expected quality of service.

One of the key types of signal fades that occur on microwave systems is a rain fade. A rain fade is the signal loss that results from signal absorption and scattering in water droplets (rain).

Line of Sight (LOS)

Line of sight (LOS) is a direct path in a wireless communication system that does not have any significant obstructions. WiMAX systems that operate in the 10-66 GHz range are LOS systems.

Non Line of Sight (NLOS)

Non line of sight (NLOS) is a wireless communication system that does not have a direct path (can have significant obstructions) between the transmitter and receiver. NLOS systems can use radio signals for transmission.

Figure 1 shows how non line of sight (NLOS) radio propagation can allow a radio signal to reach its destination in congested areas. A radio tower is transmitting through an urban area which does not allow a radio signal to travel a direct path from the tower to the receiver. Accordingly, multiple alternate paths are reflected off a building to reach its destination. A main signal (shortest reflected signal) and another signal (delayed signal) become part of the received signal.

Figure 1: Near Line of Sight Radio Propagation

Saturday, September 19, 2009

WiMAX Radio Overview

A WiMAX radio channel is a communications channel that uses radio waves to transfer information from a source to a destination. It may transport one or many communication channels and communication circuits on a single RF channel.

WiMAX radio channels may operate within different frequency bands, have different radio channel bandwidths, dynamically change modulation types, use a variety of access technologies and other characteristics that allow WiMAX to reliably provide a variety of types of communication services.

The WiMAX radio systems can use a single carrier (SC) or multi-carrier (MC) transmission. Single carrier transmission is the use of a single carrier wave that is modified to carry (transport) all of the information. Multi-carrier is a communication system that combines or binds together two or more communication carrier signals (carrier channels) to produce a single communication channel. This single communication channel has capabilities (capacity) beyond any of the individual carriers that have been combined. When each of the carriers in a multi-carrier system is mutually independent (orthogonal) to each other, it is called orthogonal frequency division multiplexing (OFDM).

Figure 1 shows the key components of a basic WiMAX radio system. The major component of a WiMAX system include subscriber station (SS), a base station (BS) and interconnection gateways to datacom (e.g. Internet) and telecom (e.g. PSTN). An antenna and receiver (subscriber station) in the home or business converts the microwave radio signals into broadband data signals for distribution. In the example, a WiMAX system is being used to provide telephone and broadband data communication services. When used for telephone services, the WiMAX system converts broadcast signals to an audio format (such as VoIP) for distribution to IP telephones or analog telephone adapter (ATA) boxes. When WiMAX is used for broadband data, the WiMAX system also connects the Internet through a gateway to the Internet. The WiMAX system can reach distances of up to 50 km when operating at lower frequencies (2-11 GHz).

Figure 1: WiMax System
Related Posts with Thumbnails