Wednesday, May 9, 2012

FORWARD ERROR CORRECTION AND RATE ADAPTATIONS | ADAPTATIONS AT THE MAC LAYER



FEC allows the WiMAX MAC layer to detect errors introduced during the transmissions of frames over the air link. There are three methods of FEC specified in the WiMAX system; Reed-Solomon concatenated with convolutional code (RS-CC), block turbo code (BTC), and convolutional turbo code (CTC). RS-CC is mandatory, while BTC and CTC are made optional due to their complexity, eventhough they provide 2–3 dB better coding gain than RS-CC. For the 802.16e, a hybrid ARQ (H-ARQ) has been included as an optional feature. There are three types of H-ARQ, classified based on the manner in which they handle the retransmissions. 

Type I H-ARQ retransmits lost or unacknowledged blocks using chase combining in which the old erroneous block is stored at the receiver and compared with the retransmitted copy. This helps to increase the probability of successful decoding at the FEC block during the retransmission attempts. Type II/III H-ARQ uses incremental coding rate to ensure successful decoding at the FEC block during the retransmission attempts. Rate adaptation works hand-in-hand with the FEC block in the WiMAX system. When a user experiences good channel condition, it is desirable to exploit these peaks in the channel gain to increase throughput. 

This is achieved by having the SS increase the coding rate, e.g., from rate 1/2 code to rate 1/4 code, so that more information bits can be transmitted per channel use while still keeping to the target bit error rate (BER). When the channel degrades, the rate is reduced back to the next minimum to ensure that the target BER is met. This dynamic process is carried out on a frame-by-frame basis in the WiMAX system, using the flexibility provided by MAP signaling to adaptively adjust the UL/DL rates.

Sunday, May 6, 2012

ADAPTIVE MODULATIONS, POWER, AND CODING RATE CONTROL



In wired networks the channel impairments tend to be constant or at least very slowly varying. Wireless networks in contrast are well known for rapidly fluctuating channel conditions even when the transmitter and receiver are stationary. Broadly speaking, the lower the modulation and coding rate, and the higher the transmitted power, the more channel fading a system can tolerate and still maintain a link at a constant error level. It is desirable therefore to be able to dynamically change the transmitted power, modulation, and data rate to best match the channel conditions at the moment to continually support the highest capacity channel possible. WiMAX systems support adaptive modulation and coding on both the downlink (DL) and uplink (UL) and adaptive power control on the UL. Adaptive modulation allows the WiMAX MAC layer to adjust the signal modulation rate depending on the channel or radio link quality. When the channel quality is good, the MAC layer chooses the highest modulation rate, e.g., 64QAM, giving the system the highest throughput. When the channel quality degrades, the MAC layer reduces the modulation rate, e.g., 16QAM, reducing the throughput. In practice, adaptive modulation and coding rate control are used in conjunction with power control. In the PMP network deployments with multiple users in a cell serviced by a BS, when a link degradation arises for a user, the BS first increases the transmitted power of the user to provide extra link budget gain, until it reaches the maximum permitted. If the received signal quality does not improve, then the coding rate is reduced. Extra redundancy is added to provide more coding gain for better error correction performance. If the received signal quality still does not improve, then the modulation rate is reduced as a last resort (as this significantly affects the throughput than others). Similar (reverse) process is also followed when link quality appreciates. For WiMAX mesh networks using the amplify-and-forward relaying option, mesh relaying cannot exploit adaptive modulation technology because relaying nodes are not able to decode the contents of the received OFDM symbols to retrieve the modulated data and remodulate them at higher or lower rate, to increase or reduce the transmission rate (or throughput) of the mesh streams in response to link quality condition. However for mesh networks using the decode-and-forward relay option, adaptive modulation and coding rate control can benefit the mesh relaying operation as mesh nodes can decode the mesh data streams and adjust the coding and modulation rate, depending on the forwarding link quality. For example in Figure 1 a relay node R decodes a data stream originally transmitted from the source node S using 16QAM modulation, and remodulates the data stream using 64QAM as it has good channel quality to the destination node D that can support this modulation rate. This results in fast and efficient use of the mesh links. Power control is applicable in WiMAX networks (PMP and mesh) in two ways: One, when nodes are transmitting data, they are regulated to transmit only the minimum power required to achieve successful reception at the receiver. Two, when mobile nodes do not have data (mesh relay or access service data) to transmit or receive, they go on sleep modes to save battery life.

 
Figure 1: Adaptive modulation at WiMAX mesh nodes.

Wednesday, April 4, 2012

ADAPTIVE ANTENNA AND BEAMFORMING SYSTEMS IN WIMAX



1 Beamforming

Beamforming takes advantage of interference to change the directionality of an antenna array system. A beamformer controls the amplitude and phase of the signal at each transmitting antenna element, to create a pattern of constructive interference (beamspots) and destructive interference (null) in the wavefront. To create a beamspot, the beamformer uses an array of closely spaced antennas, often enclosed in a single enclosure as illustrated in Figure 1. λ/2 antenna spacing between the antenna elements is commonly used (where λ is the wavelength of the transmitted signals, given by λ = c/f; f is the frequency of the transmitted signals, c is the speed of light). By varying the amplitude and phase of each antenna element, the beamformer is able to focus electromagnetic energy (beam) in the desired directions. The beams are directed to intended users, while nulls are focused on other unintended users reducing interference to the unintended users while increasing received SNR for the intended user. This provides a stronger link to the intended user and improves reach and capacity.

 
Figure 1: Beamforming technique.


2 Adaptive Antenna System

AAS is one of the advanced antenna technologies specified in the WiMAX standard to improve performance and coverage. In the AAS system, the transmitter (base station, BS) adaptively tracks a mobile receiver as it moves around the coverage area of the transmitter (BS), and steers the focus of the beam (beam spot) on the receiver unit as it moves. The beam steering method can either be mechanical or electronic. Thus AAS creates narrow beams to communicate with desired user device, which helps to reduce interferences to unintended user devices and improves carrier-to-interference (C/I) and frequency reuse, giving rise to high spectral efficiency. Thus, through the use of adaptive processing (beam steering), AAS improves performance and coverage of the system significantly. In WiMAX networks, AAS will find wide applications both in the point-to-multipoint (PMP) as well as mesh network deployments. In the PMP mode, AAS operates in similar way as in the current 3G cellular system, and is used for enhancing coverage and performance. In the mesh mode, AAS is used to form physical or directed mesh links. Physical or directed mesh is a form of mesh where substantially directional antennas are used to create physical links between neighboring devices. Mesh nodes adaptively steer antennas towards other nodes in their neighborhood and direct the focus of the electromagnetic radiations accordingly, to create the physical link with the intended neighboring device. One of the main drawback of AAS however is the high complexity involved in designing antenna systems capable of adaptively switching (steering) antenna directionality toward users who may be highly mobile. The use of AAS technology in mobile network deployment is therefore very challenging from a complexity perspective. Another drawback of AAS technology is that in an urban environment, with rich scatterer, the beams get blurred at the receiver and are not focused as expected, due to the reflections of waves as it propagates from the transmitter to the receiver. This effect is known as angle spread and it impacts significantly the performance of AAS in urban areas with cluttered structures. The gains achieved using AAS in such places thus reduce considerably from the theoretical expectations. For example, an AAS system using an eight-column array would have an ideal gain of 6.9 dB but angle spread would reduce this to only 3.2 dB in an urban environment and 4.7 dB in a suburban environment. There are some techniques however to mitigate the effects of angle spread. Active research works are ongoing in this area
Related Posts with Thumbnails