Showing posts with label Operational Support System. Show all posts
Showing posts with label Operational Support System. Show all posts

Thursday, April 14, 2011

SLEEP MODE OPERATION IN WIMAX RELAYING NETWORKS


In the forthcoming IEEE 80216j standard, sleep mode operation has also been incorporated. In such relay networks, a BS coordinates all communications to and from subscriber stations. Although the initial standard provides a large coverage distance of up to 50 km under line-of-sight (LOS) conditions and typical cell radii of up to 8 km under non-line-of-sight (NLOS) conditions, there was still a huge demand for enhancing the network coverage without compromising system throughput. One of the possible options to achieve this was to introduce relay stations (RS) which bridge the communications between an SS out of coverage and the BS [9]. The great advantage of this multihop communication concept is that coverage is extended with cheap devices at a small cost of throughput degradation. RSs are divided into three categories, namely fixed RS (FRS) which are installed at fixed locations, nomadic RS (NRS) installed for a specific time duration, and mobile RS (MRS) which are mobile units operating with battery cells (Figure 1).

 
Figure 1: Sleep mode in IEEE 802.16j multihop networks.

Useful deployment of MRS with a battery power source or low-power fixed/NRS powered by solar power or battery require high-power efficiency. Moreover, this feature reduces the interference generated by RSs. Here, we briefly describe how sleep mode can function in relay scenarios.

In a centralized scheduling system, where the network is coordinated by the BS (named in Relaying Networks as MR-BS), the MR-BS informs all the stations of the network including both the RSs and the MSs, about listening and sleeping windows. In a second phase, the RS coordinates with the MSs the finding of common availability and unavailability intervals. If all the MSs connected to a single RS are sleeping then the RS can enter the sleep mode too. Similar to the initial IEEE 802.16e standard, the RS can request activation of RS sleep mode by sending RS_SLP-REQ message to the MR-BS. Note that now respective message types begin not with MOB as before but with RS.

In order for the RS to generate the listening and sleep windows, via a RS_SLP-REQ, the RS shall keep record of the information sleeping patterns of associated MSs. When an RS enters sleep mode it can be awakened by the serving MR-BS or by itself. The MR-BS can use the existing MOB_TRF-IND to awaken a sleeping RS.
Sleep Mode can be divided into
  • Full RS Sleep Mode: This mode is entered if there is traffic at any relay and access link while the RS stays in sleep mode. All associated RSs and MSs connections are suspended RS sleeping.

  • Partial RS Sleep Mode: This mode is similar to the previous case. The difference is that certain management messages are sent at predefined intervals to support MS network entry, re-entry, and handover.
A question remains whether these mobile relay stations can withstand the heavy usage. To what extent can such a terminal survive only on battery, and how energy efficient can IEEE 802.16e be in case of distributing information to many nodes?

Friday, April 2, 2010

Support of Beamforming in the IEEE 801.16 Standards


Add a Note HereBeamforming is defined in IEEE 802.16-2004 and in 802.16e. This feature is not in the set of the fixed WiMAX profiles. For the mobile WiMAX profiles, this feature is mandatory to be supported by the MS and optional for the BS. For the mobile WiMAX, several mechanisms that enhance the performance and operation of beamforming are provisioned.
Add a Note HereIn the downlink, in order to be able to beamform several users at the same and on different subchannels, a zone is dedicated (indicated in the DL-MAP). This region, labelled (2) in Figure 1, contains permutations with dedicated pilot channels. This means that an MS receiving a burst in this region only takes as valid pilots the pilots associated with the subchannel it has been allocated.

Add a Note HereFigure 1: Example of a frame with regions supporting AAS operation
Add a Note HereIn the uplink, as mentioned previously, the beamforming mechanisms can be applied on any MS. However, to improve the performance and to help the BS in detecting/measuring the interference experienced by the users it wants to serve, a specific signalling zone may be allocated: the uplink sounding zone (indicated by UIUC=13). Actually, the BS may ask some MS to transmit a signal in this zone so that the BS can evaluate the interference on some subcarriers for those MSs.

Add a Note HereFinally, in order to limit the signalling overhead, the WiMAX solution employing beamforming may use the compressed maps and submaps to transmit the common signalling messages (DL-MAP/UL-MAP). Indeed, this permits different modulation, coding and repetition schemes to be applied to several zones in the DL-MAP/UL-MAP message. This solution can also be employed in the case of MIMO or the support of the HARQ.

Saturday, August 29, 2009

Base Stations, Packet Switches, Operational Support System

A base station is a radio access transceiver (combined transmitter and receiver) that is used to connect subscriber stations to a WiMAX system. Base stations convert and control the sending of data packets and can connect one or many wireless devices to a backbone network.

Base stations can perform one or many types of data transfer functions including bridging (linking networks), retransmitting (repeating), distributing (hubs), directing packets (switching or routing) or to adapt formats for other types of networks (gateways).

Indoor Base Stations

Indoor base stations are devices or assemblies that enable systems or system connections to receive and convert radio or communication signals that are enclosed and/or have connections that allow them to be used in indoor environments.

Outdoor Base Stations

Outdoor base stations are devices or assemblies that enable systems or system connections to receive and convert radio or communication signals that are enclosed and/or have connections that allow them to be used in outdoor environments.


Packet Switches

A packet switch is a device in a data transmission network that receives and forwards packets of data. The packet switch receives the packet of data, reads its address, searches in its database for its forwarding address, and sends the packet toward its next destination.

Packet switching is different than circuit switching because circuit switching makes continuous path connections based on a signal’s time of arrival (TDM) port of arrival (cross-connect) or frequency of arrival. In a packet switch, each transmission is packetized and individually addressed, much like a letter in the mail. At each post office along the way to the destination, the address is inspected and the letter forwarded to the next closest post office facility. A packet switch works much the same way.

Operational Support System (OSS)

Operations support systems are combinations of equipment and software that are used to allow a network operator to perform the administrative portions of the business. These functions include customer care, inventory management and billing. Originally, OSS referred to the systems that only supported the operation of the network. Recent definition includes all systems required to support the communications company including network systems, billing, and customer care.

Related Posts with Thumbnails