Showing posts with label sleep mode. Show all posts
Showing posts with label sleep mode. Show all posts

Thursday, April 14, 2011

SLEEP MODE OPERATION IN WIMAX RELAYING NETWORKS


In the forthcoming IEEE 80216j standard, sleep mode operation has also been incorporated. In such relay networks, a BS coordinates all communications to and from subscriber stations. Although the initial standard provides a large coverage distance of up to 50 km under line-of-sight (LOS) conditions and typical cell radii of up to 8 km under non-line-of-sight (NLOS) conditions, there was still a huge demand for enhancing the network coverage without compromising system throughput. One of the possible options to achieve this was to introduce relay stations (RS) which bridge the communications between an SS out of coverage and the BS [9]. The great advantage of this multihop communication concept is that coverage is extended with cheap devices at a small cost of throughput degradation. RSs are divided into three categories, namely fixed RS (FRS) which are installed at fixed locations, nomadic RS (NRS) installed for a specific time duration, and mobile RS (MRS) which are mobile units operating with battery cells (Figure 1).

 
Figure 1: Sleep mode in IEEE 802.16j multihop networks.

Useful deployment of MRS with a battery power source or low-power fixed/NRS powered by solar power or battery require high-power efficiency. Moreover, this feature reduces the interference generated by RSs. Here, we briefly describe how sleep mode can function in relay scenarios.

In a centralized scheduling system, where the network is coordinated by the BS (named in Relaying Networks as MR-BS), the MR-BS informs all the stations of the network including both the RSs and the MSs, about listening and sleeping windows. In a second phase, the RS coordinates with the MSs the finding of common availability and unavailability intervals. If all the MSs connected to a single RS are sleeping then the RS can enter the sleep mode too. Similar to the initial IEEE 802.16e standard, the RS can request activation of RS sleep mode by sending RS_SLP-REQ message to the MR-BS. Note that now respective message types begin not with MOB as before but with RS.

In order for the RS to generate the listening and sleep windows, via a RS_SLP-REQ, the RS shall keep record of the information sleeping patterns of associated MSs. When an RS enters sleep mode it can be awakened by the serving MR-BS or by itself. The MR-BS can use the existing MOB_TRF-IND to awaken a sleeping RS.
Sleep Mode can be divided into
  • Full RS Sleep Mode: This mode is entered if there is traffic at any relay and access link while the RS stays in sleep mode. All associated RSs and MSs connections are suspended RS sleeping.

  • Partial RS Sleep Mode: This mode is similar to the previous case. The difference is that certain management messages are sent at predefined intervals to support MS network entry, re-entry, and handover.
A question remains whether these mobile relay stations can withstand the heavy usage. To what extent can such a terminal survive only on battery, and how energy efficient can IEEE 802.16e be in case of distributing information to many nodes?

Monday, April 11, 2011

PERIODIC RANGING IN SLEEP MODE | Power Management in Mobile WiMAX


The standard defines periodic ranging in sleep mode functions in great detail. Ranging is a very important mechanism in IEEE 802.16 networks since the MS is using it to adjust the power and sychronize with the OFDM symbol. When the MS is in sleep mode, the ranging uplink transmission can be allocated in three different ways.
  1. During the listening window, a BS may allocate an uplink transmission opportunity for periodic ranging.

  2. A BS can activate a PSC type III to keep the MS in active state until the assignment of an uplink transmission opportunity for periodic ranging.

  3. As mentioned above, the RNG-RSP (or MOB_SLP-RSP) can include the next periodic ranging TLV. From this the MS may know when the next periodic ranging opportunity shall occur. From the next periodic ranging TLV a MS may decode all consequent UL-MAP (uplink MAP) messages waiting for an uplink unicast transmission opportunity. When its own opportunity takes place the ranging procedure can be executed as normal.
It is important to mention that successful ranging does not deactivate the PSCs. After successful ranging, the BS announces the next ranging time in an RNG-RSP message. Additionally, if there is downlink traffic in the BS’s queue then a DL traffic indication is addressed to the MS. This way, the MS can exit the sleep mode algorithm earlier and reduce the imminent response delay.

Sunday, August 1, 2010

Energy Conservation via Sleep Mode

Need for "Sleep" and "Wakeup" Modes
The simplest way to save energy and thus prolong the battery life of a SS is to put the SS to "sleep" (i.e., kill all processes running on the SS except for the minimum required to sustain the connection) when it is not involved in any communications. During the sleep period, the SS will not transmit, but "listen" to the channel occasionally to maintain connectivity. This feature is not specified in the 802.16-2004 standard, as that standard was proposed for stationary SSs and it was assumed that power supply for the SSs would not be a critical problem.

Clearly, an SS in the sleep mode requires a complementary mechanism for "waking up" so that it can resume transmitting or receiving. The signaling message that accomplishes this is usually called the "paging" signal. Again, the 802.16-2004 standard does not include a paging signal either.

Message Exchanges to Enter Sleep Mode
We propose the following sequence of steps before an SS enters the sleep mode.

Based on a lack of traffic on the DL and UL, the SS decides that it should enter the sleep mode. Thus, the decision to enter the sleep mode is SS-initiated. The algorithm that the SS applies to arrive at this decision is arbitrary, and can be specific to that SS alone while being unknown to the BS.

The SS uses a CID belonging to one of its current sessions to send a bandwidth request (BR) message to the BS. This is the mechanism for requesting additional bandwidth specified in the current 802.16-2004 standard. As it is very unlikely for a SS to specify 0 bytes in the BR message (i.e., requesting zero additional bandwidth), we propose for the BS to interpret such a message from the SS as a request for permission to enter the sleep mode. A key advantage of such use of BR message with 0-byte request is that if the BS is not enabled to support this sleep/wakeup function, then a request for an additional bandwidth of zero bytes will simply be ignored or discarded, thereby causing no changes to the current session.

If the BS is capable of supporting sleep/wakeup in the SS, then it includes a pre-specified Uplink Interval Usage Code (UIUC) that serves as an acknowledgment to the SS that it is allowed to enter into the sleep mode. The specific UIUC is known and hard-wired in the BS and SS.

On receipt of this acknowledgment message from the BS, the SS enters the sleep mode after a fixed time interval (measured in the number of frames), which is set by the network operator and assumed known to both the BS and the SS. This obviates the need to transmit this interval defining the sleep start time from BS to SS or vice versa, thereby eliminating the need to change the standard to accommodate a message that does so.

During the sleep mode, the SS maintains frame synchronization (this is one of the few processes that are maintained during the sleep mode). Further, the SS decodes DL information periodically to check whether the SS is being "paged" by the BS (see the description of the "wakeup" subsequently). The period (e.g., once every five frames) is predefined by the network operator and hard-wired in the SS. Battery energy is conserved as the SS decodes data occasionally.

Note that from the perspective of the BS, the SS is treated just the same as if it were not in the sleep mode, with the exception that the BS does not transmit data to a sleeping SS without first ensuring that the SS has been waken up. The session parameters associated with a sleeping SS are retained.

The sleep period is not indefinite, but continues only for a finite number of frames, after which the SS wakes up by default if it has not already been waken up by a paging message sent from the BS, or by the arrival of data at the SS intended for transmission on the UL. This maximum sleep duration is also predetermined, fixed, and set by the network operator and assumed to be known to both BS and SS.

Message Exchanges to Wakeup a Sleeping SS
1. SS Wakes Up on Its Own
If the SS has any data to send on the UL to the BS, it simply wakes up by reviving all processes that were running before it entered the sleep mode, and then transmitting the data just as it would have if it had never entered the sleep mode. As the BS retained all session parameters when the SS first entered the sleep mode, the BS is ready to receive the data and does so. The arrival of this data from the SS alerts the BS to the fact that the "sleeping" SS has now woken up by its UL transmission. The BS then treats the SS as if it is no more in sleep mode.

2. BS Wakes Up the SS via a Paging Message
The BS wakes up a sleeping SS by transmitting a "paging" message during one of the periodic frames that is received and decoded by the SS. A specific "paging" message is not supported by the current 802.16-2004 standard. However, the standard permits network operators to use several UIUCs to define modulation and coding rates (burst profiles) for both the orthogonal frequency division multiplexing (OFDM) and OFDMA modes of operation. The network operator may therefore reserve one of these UIUCs for "paging." The steps involved in waking up a sleeping SS to receive DL data is given next.

In the UL-MAPs transmitted by the BS over a number of consecutive frames, the BS specifies the CID of the SS scheduled for wakeup, employing the UIUC designated for "paging" purposes with the most robust modulation and coding scheme available. The reason for this is that the SS is only receiving and decoding periodic frames during sleep mode. Further, as the sleeping SS does not transmit anything on the UL, the BS has no information about DL channel quality, and cannot tailor its coding scheme accordingly. Thus, if the DL channel suffers degradation, the SS may not receive the BS transmission, so robust modulation/coding with repetition maximizes the chance of the SS receiving the paging "message."

Upon receiving the UIUC information in the UL-MAP, the SS exits the sleep mode. To confirm with the BS that the SS has indeed exited the sleep mode, the SS transmits another bandwidth request message with 0 bytes in the BR field. The receipt of this message by the BS is interpreted by the BS as an acknowledgment by the SS that it has now "woken up" and resumed normal operation.
Related Posts with Thumbnails